Montgomery Wards Powr Kraft Lawn Tractor


[ Save This Page ] [ Follow Ups ] [ Post Followup ] [ Lawn Tractor / Garden Tractor Discussion Forum ] [ FAQ ]

SSB Farm Tractor Parts, Manuals & Antique TractorsAftermarket Farm & Old Antique Tractor PartsTractor Service, Repair & Owners Operators Manual ShopTractor ImplementsTractor SeatsTractor Front End LoadersPedal Toy Tractors Farm Tractors For Sale ClassifiedsAntique Tractors For Sale ClassifiedsTractors Forum - Help & AdviceTractor, Gardening, Mowers & Outdoor Equipment BooksTractor ProductsContact Us
SEARCH MANUALS
FIND PARTS
How much is your farm tractor worth? Find resale prices for tractors built from 1939 and 2011, with complete specifications and serial numbers. Save 15% on our Official Tractor Blue Book sale!

Search This Message Board:

Montgomery Wards Powr Kraft Lawn Tractor

Fred Mead I need a owners manual for a Powr Kraft 18hp 42"
Lawn tractor. How to adjust drive belt . This is hryrostatic trans.

Fred Mead I need a owners manual for a Powr Kraft 18hp 42"
Lawn tractor. How to adjust drive belt . This is hryrostatic trans.

Sam I have an owners manual. It covers the following
models:

42 inch (two blade) 18 HP TMO 3500006

46 inch (three blade) 18 HP TMO 3400005A

These are actually MTD mowers and I am able to
order parts using the part numbers out of the
owners manual at the following web site

www.outdoordistrubutors.com

If you want a copy of this operating manual
please contact me at samova@yahoo.com

Sam I dont think there is an adjustment. When you lower the deck to cut grass it automatically gets tight. If it dosent then it is worn out and you need to buy a new belt. Order part
number 754-0441 V-Belt for an MTD mower at the following web site. This belt fits both the
42 inch and 46 inch mowers.

www.outdoordistriburtos.com

Sam I dont think there is an adjustment. When you lower the deck to cut grass it automatically gets tight. If it dosent then it is worn out and you need to buy a new belt. Order part
number 754-0441 V-Belt for an MTD mower at the following web site. This belt fits both the
42 inch and 46 inch mowers.

www.outdoordistributors.com

Sam As far as what side to sharpen. When you install
the blade make sure the bent part of the blade is pointed up. Then watch the way the blad turns and it should be obvious what edge to sharpen.

Ron
Where can I find front end parts for a
PowrKraft 15-42 mower ? I need front steering
crossmember piece Thanks,

Ron

Ron

OK ... I found what I needed ... Thanks

Wayne I have a 18.5/46", twin cylinder, Auto. transmission, hydrostatic drive - Industrial/Commercial mower. Model 3500007, Limited Edition. The headlights do not work and I'm not sure if it's just the lamps are out or if the wiring gone bad. Other than that it's in good working condition, and just had a major tune-up. I would like to sell it but have no idea of what it's worth or what I could get for it... any ideas??
Raymond Courture I have an 18.5/46" 3 blade deck. THe bearings that support the blades which have 'gear' like teeth to engage the blades have sheared off the gear teeth for the bearing shafts. Those must be replaced. The blade teeth are still intact. Occurred probably cutting heavy grass and brush. Is Model 3500007 the correct Model number for this trctor as I can't find the model # on it. Only Powr Kraft 18.5/46 Hydralic transmission twin Cylinder is on it. I would like to order a manual for his tractor as well.

Ray Courture

Robin I just purchased a Powr Kraft 18/46" Industrial/Commercial twin cylinder riding mower from my brother, he forgets what battery goes in the mower can anyone help me find this information out? I would also like to find an owners manual for this mower it is either a PMO or a TMO 3400005A.

Sam You can covert the Montgomery Ward TMO model number to a MTD model number at

http://www.mtdproducts.com/home.jsp

go to service and support and search for
montgomery ward

Jeff P I too have a TMO-3400005A 46" riding lawn mower made by MTD. I purchased it at Montgomery Wards years ago. I believe the fluid in the transmission is low. This happened over time when the mower was turned on its side. What type of fluid does it take? If I remember correctly it is red like transmission fluid. How do I fill it? It is sluggish and even locked up.

thanks,
jeff

Jeff P I too have a TMO-3400005A 46" riding lawn mower made by MTD. I purchased it at Montgomery Wards years ago. I believe the fluid in the transmission is low. This happened over time when the mower was turned on its side. What type of fluid does it take? If I remember correctly it is red like transmission fluid. How do I fill it? It is sluggish and even locked up.

thanks,
jeff

Jeff P I too have a TMO-3400005A 46" riding lawn mower made by MTD. I purchased it at Montgomery Wards years ago. I believe the fluid in the transmission is low. This happened over time when the mower was turned on its side. What type of fluid does it take? If I remember correctly it is red like transmission fluid. How do I fill it? It is sluggish and even locked up.

thanks,
jeff

Jeff P I too have a TMO-3400005A 46" riding lawn mower made by MTD. I purchased it at Montgomery Wards years ago. I believe the fluid in the transmission is low. This happened over time when the mower was turned on its side. What type of fluid does it take? If I remember correctly it is red like transmission fluid. How do I fill it? It is sluggish and even locked up.

thanks,
jeff

Jeff P I too have a TMO-3400005A 46" riding lawn mower made by MTD. I purchased it at Montgomery Wards years ago. I believe the fluid in the transmission is low. This happened over time when the mower was turned on its side. What type of fluid does it take? If I remember correctly it is red like transmission fluid. How do I fill it? It is sluggish and even locked up.

thanks,
jeff

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

Mitch Garstang I need the square shank drive shaft/U-joint that connects the mower deck to the tractor. also interested in chipper/vac/dump cart, garden plow, tiller, sickle mower & hydro drive/lift for same.
Email me if you have anything

rick thomas gentlemen
My best friend passed away may 30th and he left me a powr kraft 18.5/46 lawn tractor its in mint condition as he bought it for his 12 acre farm used 3 days parked it and bought a full size tractor. it sat for 4 years, after i cleaned it up changed the oil, gas, and spark plugs it ran like brand new. my question is i need to purchase a seat as the weather rotted out the orginal padding and i dont feel like setting on bolts. i also have the trailer that u pull behind it . question are there asecessories that can be purchased example a rototiller that has its own power source as this tractor doesn't have a pto (hydralic power take off) or if not is the sears or penny's version compatible ? or who is the orginal manufacture of this unit I'm assuming its a private label manufactured by a major manufacturer like john deer for example. I would appreciata any and all information you can provide and if you prefer you can call me direct collect is fine just e mail me and I'll give u my phone number . thanks so much for any and all help each of you can provide me. I live in kingman arizona so if any of you responding to this and live close I have no problem meeting and discussing this futher. thanking all of you in advance for any help or information you can provide.
Sincerely

Riok thomas

Fred Mead Contact Jack's Lawn and Garden Repairs
the Tractor was made by MTD He will have information as well as new and used parts and will
sell yo an owners manual phone Jack 503- 422-8347
leave a message and he will return your call.
F Mead.

Sandra I desperately need a manual for the above subject. Where can I obtain one?
Scott Just picked up a 18/42 that was made in 1990. Any clue if they sell a snow plow for this model and where would I look?
Steve Ford I need a manual for mower POWR KRAFT 18.5/46 TMO 3400005. IO also need the electrical manual if possible. Please let me know where I can find this information.
JASON COLLINS IF YOU NEED A MANUAL FOR 18/46 TRY CALLING 1800-323-1965. YOU CAN ORDER ANY OF THE PARTS FOR THIS & OTHER MODELS.
Kenneth Benn powr kraft rider 18hp twin 2 briggs & stratton,model 422707.need help.start hard,wondering if deck belt could to tight? what is belt number? Thanks Ken
Steve I have a Powr Kraft 18/42 mod# TMO 3500006 134Q699GO88. There is a snow thrower attachment 40" 2 stage mod # 190-621-000 attached to it. I would like to remove snow thrower and attach mower deck. I have no manuals and need help.
Juanita Wilson Looking for choke cable

Part # 746-0614A FH10

Can you help me get one?

Thank you

jackie white have new belt but not sure how to put it on for the mower deck could someone please send me a diagram ?
jackie white could someone please send me a diagram of how to put the deck belts on thank you

Kelly Thompson I just received a Powr Kraft 18/46 riding mower from my son, the only info I can find on it is 18/46 Automatic Transmission Hydrostatic Drive. Where would I find a model number on it, so I can try to get an owners manual. Help.
Marie Cusson Where can replacement blades be found for a Powr Kraft 18/42 Model TMO3500006? Would appreciate some help.
Jeff_p See my May 9, 2004 posting for the model #
Jeff_P TMO-3400005A for the 46"
Ray Courture I bought mine at WalMart. Just measure the size of your current blades and look for a set of blades with simular type holes and lenght. You might take one of the old blades with you for comparison.

Lionman of Oregon

Marie Cusson Thank you!
Eric I have a wards Tractor model number GIL-33048A I Need anew Driveshaft is is hydrostatic drive any help where I could find one of these would be greatly appreciated
Kelly If you contact the man named Jack that is in the info on this website he will call you back and he knows these mowers and where to get parts. Mine doesn't have a model number behind the seat as everyone states, but I'm going with what most replys have told me, TMO 340005A
Kelly I got some at Walmart also. They don't have the star shaped hole in the middle, but they worked all but the middle one. I have a three blade model and the middle blade seems to be shorter.
dustin I have a powr craft 18.5/42 riding lawn mower. The steering rod which connects to the front wheels to make them turn right or left snaped in half. montgomery ward is no longer in our area. I tried a lookup on sears site for a part, however the did not reccognize the number. Is there any other ideas you might have. model number tmo 3650002136s699g088. Thanks in advance.
Al My mower is the 18/46 mower and one of the plastic pulley's underneath that tightens the mower belt is worn beyond belief. It is attached to a sort of bracket arm and I definately need a replacement. Any ideas? Any help?
Sam Go to Sears website www3.sears.com

look up lawn tractor model number 3500006

Webster Cole I need a shift plate for a 18HP 42" cut Powr Kraft Riding Mower by Montgomery Ward. It is a Hydrostatic Limited Edition. Where can I find this part.
Sam Yes. Just go to Sears lawn tractor parts site http://www3.sears.com/
and search for this number under MTD brand name

3500006

Sam Sears has them

go to http://www3.sears.com/

and search for this model number under MTD brand name

3500006

Sam No. The belt is not too tight. The problem is your air cleaner. It is all clogged up and the engine cannot breathe. Replace your air cleaner and it will start right up.
Richard Christensen have a 18.5/46", twin cylinder, Auto transmission, hydrostatic drive, and Industrial/Commercial mower model 3500005A, Limited Edition. I NEED THE PARTS LIST AND DRAWING OF THE HYDROSTATIC DRIVE. Can somebody help me locate them? In addition, the mower service manual would be helpful. All ideas wel
Sam The Hydro Drive is not broken down in the drawings. It is sold as a whole unit only.
You can get a parts breakdown and parts from Sears Tractor Parts Site at http://www3.sears.com/
look for MTD model number
3500006 (make sure you have four zeros)

kent w Ref. a Powr Kraft 18/46
Im having a problem with the tractor slipping while going up hills, and it is progresivly getting worst. I first thought it was the drive belt. so i replaced it, and it did not fix the problem. So now I believe it may be a problem with the automatic transmission. There is a black hose with a red cap on the end underneath the plate in front of the seat. Is this where I add the transmission fluid, and has anyone else experienced this problem, and what did you do to fix it. thanks

Richard Christensen Can any one help in answering these questions.
I have a Montgomery Ward 18.5/46", twin cylinder, Auto. Transmission, hydrostatic drive - Industrial/Commercialí Model 3500005A, Limited Edition mower. I do not have a service manual. How do I go about checking the level of hydrostatic transmission oil? What should the oil level be at? What type of replacement oil is recommended?
Richard Christensen

Gary Ebert I just spent 2 hours completely disassembling an 18/42 that supposedly runs great. The steering gears are all messed up. A manual would be great.

Thanks for offering it.

Ray I have a Powr Kraft 18/64 Automatic Transmission
Limited Edition
Twin Cylinder
Industrial Commercial
Riding lawn mower,and I need to know if this mower uses trans fluid and if so where do you put it

frank e having problems starting my mower,when i turn the key i only get a clicking sound from under the seat i took this bottum plate and found my positive and ground wire hooked up to something like a solenoid that leads to my starter could this be the problem
Roger Krieger Can you send a copy of the manual for my Ward Tmo 3500009. Thanks
Dale Go to this website. It has the complete drawings for the Powr Kraft Lawn Tractors.
http://wssemw.arinet.com/Empartweb52/scripts/EmpartISAPI52.dll?MF

KB Found all the info I needed for my Powr kraft 18hp 42" rider at this site (MTD) http://support.mtdproducts.com/cgi-bin/mtd.cfg/php/enduser/std_alp.php
Dave Maciel Frank E. before you change the solenoid on your mower, check the battery first. I spent time asking almost the same question, and could get no answer from anyone that should have known what my problem was. If you still have the problems, send me an e-mail and I'll tell you what I did to resolve my problem. My mower is running like I had never had any problems with it.
Dan Guinan I have the 42" TMO-350006 Lawn Tractor it was running fine and now just won't start. It has always been a hard starter, especially when it was hot, not it doesn't even sound promising. I check the plugs, the filter, gas, etc. I think there is some shut off switch or something keeping it from starting, any ideas anyone? And by the way, I have the manual if anyone wants a scanned copy.
Dawn Rickman I'm looking for an owner's manual for my Model 422707. Anybody know where I can get one?
leroy steavens need bushing for model 422707 for drivers side steering.

Can you help me get find one?

Thank you


Teresa Martin I have the exact same tractor. Could use a scanned copy of the manual. Don't know where to check transmission fluid. Since it's hydrostatic, I don't want to mess it up any further. I had trouble starting mine last week. Choke was sticking, so my neighbor man fixed it. After cleaning the filter and the foam around it, it starts fine now. I don't know about any shut off switch. Sorry! I'm just trying to take care of mine properly. Don't want to have to buy another.
Philip Speasmaker Recently acquired a Powr Kraft 18/46 limited edition. Need owners manual. Can Anyone help?
Thanks

Billy 18/46 I have model #TMO-3400005A I need a battery and I would like to khow where to get one reasonable. The mower is sold
don I need a manual that shows how to hook up a snow blower to my mower. My mower is a 42" model nos. TMO-3400005A
TMO-3500006
The model no. on my blower is
GIL-1403A
Serial no. 27X1753
Thank you.

Don i need a manual that shows how to attach my sonw blower to my tractor. My tractor model no. is 3500006 or 3400005A it is a 42" 18hp. The model no on the snow blower is GIL1403A serial no is 27X17573. please email me Thank you

Randy Critchlow Need an Owner Manual for a
18/42 PowrKraft Lawn Tractor
Model Number TMO-3500006

Randy Critchlow Correction e-mail address
Ron Beller I have a Monkey ward tractor! and have all the manuals! I might be willing to sell copies. It is I believe a 1965 model. Attachments i have include:, grader blade, plow, mower deck, front end loader with regular bucket and a tine bucket, parts for a backhoe, dual wheel attachments and extra wheels, tire chains, wheel wights. books for all.
Bob Durr I have a Powr Kraft 18.5/46 mower. The deck drive pully needs to be replaced.
I ordered one (double pulley for MTD 756-0638) and the bearings just drop through the race type thing. Running it this way will cause the bearings to spin.Which is what happened in the first place.The bearings that were in it are 6203LU.
If anyone can give me the OEM part numbers for this deck I'd appreciate it.
Also if you know of a fix I'd like to hear about it.
thanks
bob


Bob Durr Forgot the model number
TMO-3600007

Don C My Power Kraft is hard to start. I rplaced the solenoid and charged and recharged the battery. Checked all the wiring, fuse etc. No luck, I would like any suggestion or help I can get, thanks.
Don

Mike I have a Powr Kraft gear-driven roto-tiller which has both forward and reverse action. Would anyone have a manual for this rototiller, or let me know how to install the rear action belt as (I believe) it must be twisted into a figure-8 in order to reverse the tines on the tiller portion.
Bob I am looking for the upper and lower steering shaft for a 46 inch deck Powr Kraft. Does anyone know where I can find a used one?
Hawk does anybody have a manual for 1996 powerkraft 42 or 46in. lawn tractor. I have also a 1996 powerkraft parts mower if anybody needs some parts.

David Niederberger I have an old 4HP Briggs/Stratton front-tine tiller that I need the washers (seals) for the tiller shaft-to-transmission connections. The seals look like "fiber" wikrh a 1" ID and about a 2" OD. The only number I can find is an embossed (raised) number underneath the guard above the tines "6130". A manual would also be helpful.
Ray My battery has been checked and is new. My mower still won't start. The starter kicks in but just barely turns th motor one time and then won't do anything.

Thanks,
Ray

Cameron Weisdorfer Does anyone know where to look for the serial number and model number on a 18/46 Powr Kraft hydostatic drive mower? According to the engine it was made in 1994. I looked under the seat and around the battery but cant seem to locate the tag. Thanks for your time and please help cause I need to get parts for the mower deck.
Ahmed Recently acquired a Powr Kraft 18/46 limited edition. Need owners manual. Can Anyone help?
Thanks

Charles Can you please tell where I can get a replacement battery for my Power Kraft riding mower. Model #TMO3500006 134Q699GO88, S/N #2H094H20070?

Thank you,

bruce My mower is an 18/46 Power Kraft hydrostatic drive and it moves very slow. What would cause this?
Raco I have an MTD 2 stage Snow attachment that does not fit my tractor, How can I find out which model or brand of garden tractor
would it fit, so I can try to sell it?? Model OEM 190-621 Serial iK056J20100

cs The bushings are worn out on the front end and it makes the steering bind up and axles wobble. Can these be replaced and if so how do I get them?
crackerjack the clyinder ignition timing isn't on
john schulder Question

Does the Model and Ser appear any where else on the tractor besides under seat on seat frame?

Thanks for any help

Terri I have a Powr Kraft 18.5/42 Industrial Commercial Ride on lawn mower...Lost the keys to it!! Know of Any place I can get a set of replacement keys..Or do i need a locksmith
Claudette I lost the keys to the lawn mower how can I get a new one
kent I found mine online at MTD, you have to know your model number and serial number, but then you can print one.
Darrell Dye I have a Power Kraft TWO3500006 134Q699G088. Csn snyone help me with 3 things. 1-Owners manual. 2-how to check transmission fluid. 3-what type of transmission fluid.
Darrell Dye I have a Power Kraft TWO3500006 134Q699G088. Can snyone help me with 3 things. 1-Owners manual. 2-how to check transmission fluid. 3-what type of transmission fluid.
Darrell Dye I have a Power Kraft TWO3500006 134Q699G088. Can anyone help me with 3 things. 1-Owners manual. 2-how to check transmission fluid. 3-what type of transmission fluid.
Dave how do i order a snow blade for this rider, interested in getting one, need parts list and price.. can anyone help?
Lisa I have a 3400005 18 HP, 46" Lawn Tractor and it is sluggish to start. It acts like it is getting no juice and then revs right up. Any ideas? Also, I have a manual for 42" and 46" Lawn Tractors, Model Nos. TMO-3400005 and TMO-3500006 if anyone needs a copy.

Thanks,

Alan I have a Powr Kraft 18/42 Still running strong. Had little trouble considering the abuse it has seen.
I noticed some people on here asked about fluid for
hydrostatic transmission and I read Motor oil like 20W50 was the spec. I use Amsoil 20W50 racing oil in mine for several years now, since original stuff went way low and tractor wouldn't move. I sucked out residual through the vent under the panel in the front of the seat. Making sure I got all of it out. Then in with the new,
approx. 1 quart. I go through lots of belts and have replaced the deck spindles, several little fuel pumps in the carb. Not much else. I religiously change the Amsoil synthetic 30 grade oil about every year. The engine is in pristine condition and no smoke, runs like hell. I want to thank those of you who have given some great info and sources as I misplaced all my parts manuals,specs etc. Thanks to all


Ozzie
Re: Montgomery Wards  Powr Kraft Lawn Tractor

FYI-checked the MTD website link posted above and was able to download 3 PDF manuals for my 18.5/46" Twin Cylinder Tractor. Extremely helpful with Operation/Maintenance manuals and Illustrated Parts/Shop Drawings, part #s, thanks to those who listed the websites!

Sally manual online:

http://www.oscar-wilson.com/MANUALS/MTD/134Q699H088.PDF

Nancee Picked up a powr kraft 15/42.. Cannot locate any tag for serial or model number. Anybody out there have it? Or know where I can find it?
Wes Murphy I have a 18.5 42" powrKraft need choke cable and throttle cable with assembly does anyone know part number or supply house for these??(805) 688-8063 for closest parts house zip 93427
Scott I have a Model 3400005 and the motor turns over very hard. I have to jump start it every time I run it. It seems that the battery is just too small for the twin cylinder engine. I also have a problem with driving up an incline when the unit has been running for 20 minutes or more. I have checked the drive belt and it is in good shape and is tight. Perhaps the hydrostatic drive unit is low on fluid. Any ideas on how to check it?
Cathy I purchased a used Montgomery Wards 18 hp, 46" cut Powr Kraft Lawn Tractor at the end of last summer. I took a couple of passes around the yard and shut it off. I decided to move it and it wouldn't start again. I have not been able to start it again. I also have a Sears LT 1000,16.5 IC OHV, 42" cut. It is bad about breaking the belts, and not wanting to run with any kind of consistency. I need to have one of the two repaired, and was hoping some of you experts out there could make recomendations as to which I should spend the money on. I have had the Craftsman repaired numerous times and it just doesn't seem to stand up. Maybe it is the repairman...lol! I truly baby my mowers, so I don't think it is due to abuse on my end. I have not spent any money to repair the Powr Craft. I have left it alone due to the severe drought and not needing to mow. Any assistance/advice you can give will be greatly appreciated.
Joe Phillips I am parting out my 94 tractor. If you need parts of any kind email me a picture and I will make you a great price on it. Body has some surface rust, deck housing is bad but all other parts are good, the 14 speed trams works well, tires are all good. Engine runs well. Send me a email if you have a interest.
leroy bushwacker hello to all,i recently had a montgomery ward lawn/garden tractor come to live with me.it is 14 hp
twin,manual tranny 3 blade deck with a model TMO33559A.i have tried this number on mtd's (and several others)site with no luck.im looking for parts manual and pretty much what ever information i can find on it.thanks so much leroy65679



[ Save This Page ] [ Follow Ups ] [ Post Followup ] [ Lawn Tractor / Garden Tractor Discussion Forum ] [ FAQ ]
Post a Followup

Name:
E-Mail:

Subject:

Comments:

Email Notification: If you check this box, email will be sent to you whenever someone replies to your message. You must include your email address above to receive this notification.


[ Save This Page ] [ Follow Ups ] [ Post Followup ] [ Lawn Tractor / Garden Tractor Discussion Forum ] [ FAQ ]

Name:
Email:  

Sign Up For Our Monthly Special Sales!